XLERATOR® Hand Dryers

Scroll over images on right to enlarge

Model XL-SB
Surface-mounted, Automatic,
Brushed Stainless Steel Cover

  • XLERATOR High Speed Energy Efficient Hand Dryer Model XL-BW
  • XLERATOR High Speed Energy Efficient Hand Dryer Model XL-W
  • XLERATOR High Speed Energy Efficient Hand Dryer Model XL-GR
  • XLERATOR High Speed Energy Efficient Hand Dryer Model XL-C
  • XLERATOR High Speed Energy Efficient Hand Dryer Model XL-SB
  • XLERATOR High Speed Energy Efficient Hand Dryer Model XL-SI

XLERATOR® Resources


Model No. Cover Finish Mounting Time Cycle Dryer Type
XL-BW White Thermoset (BMC) Surface Automatic Hand Dryer
XL-W White Surface Automatic Hand Dryer
XL-GR Graphite Surface Automatic Hand Dryer
XL-C Chrome Surface Automatic Hand Dryer
XL-SB Brushed Stainless Steel Surface Automatic Hand Dryer
XL-SI* Custom Special Image Surface Automatic Hand Dryer

*Note: Exclusive digital image technology allows for the addition of Company, School or Team logos with any color, design or a 'Green message'

GreenSpec LISTED
U.S. GREEN BUILDING COUNCIL (USGBC) LEED   

FEATURES

  • Dries Hands Completely in 10 to 15 Seconds
  • Uses 80% Less Energy
  • 95% Cost Savings vs. Paper Towels
  • GREENSPEC® Listed and Helps Qualify for LEED® credits.
  • Source Reduction Alternative
  • Promotes Hygiene

SPECIFICATIONS

Dimensions:

11 3/4" LG. X 12 11/16" HIGH X 6 11/16" DEEP
(298 MM LG. X 322 MM HIGH X 170 MM DEEP)


Weight:

16 LBS. (7.3 KGS.)


Construction

  1. Hand dryer cover shall be a one-piece, heavy-duty, rib-reinforced, die-cast zinc alloy. It shall be lightweight, unbreakable, rustproof and all exposed surfaces shall be bright chrome plated or finished with chip-proof, electrostatically applied epoxy paint and fastened to a wall plate by two chrome plated tamper-proof bolts.
  2. Hand dryer wall plate shall be equipped with (3) 7/8" (22 mm) diameter holes, one of which shall be suitable for use with surface conduit, for ease of wiring.
  3. All internal hand dryer parts shall be coated according to Underwriters' Laboratories, Inc. requirements.
  4. Entire mechanism shall be internally grounded.

Mechanism

  1. Hand dryer motor shall be a series commutated through-flow discharge vacuum motor/blower (5/8 HP / 20,000 RPM) which provides air velocity of 16,000 LFM (linear feet per minute) at the air outlet and 14,000 LFM at the hands (4 inches [102 mm] below air outlet).
  2. Hand dryer heating element (900 W) is constructed of Nichrome wire and mounted inside the blower housing, thereby being vandal proof. It shall be protected by an automatic resetting thermostat, which shall open whenever air flow is cut off and shall close when flow of air is resumed. It shall produce an air temperature of up to 135°F (57°C) at a 72°F (22°C) ambient room temperature at the hands (4 inches [102 mm] below air outlet).
  3. Hand dryer Control assembly is activated by an infrared optical sensor located next to the air outlet. The dryer shall operate as long as hands are under the air outlet. There is a 35-second lockout feature if hands are not removed.

Limited Warranty

The hand dryer shall be guaranteed to be free from defects for a period of five (5) years. Warranty shall include factory performed labor as well as the repair or exchange of defective parts, at manufacturer's option.

Units are available as specified in:
110/120V 12.5 Amp 60 hz 1500 Watts
208 V 7 Amp 60 hz 1500 Watts
220/240V 6.5 Amp 50 or 60 hz 1500 Watts
277V 5.5 Amp 60 hz 1500 Watts
Suggested Mounting Height
From Floor to Bottom of Dryer
Men 45" (114 cm)
Women 43" (109 cm)
Teenagers 41" (104 cm)
Children 35" (89 cm)
Handicapped 37" (94 cm)

Site Tools

News at Excel

Listen to what people are saying:

  • "We ordered some hand dryers from you in the past, and we are looking to purchase another 4 units. We are extremely happy with these dryers and have had ..."

    - Anonymous in the USA
  • Read more ...
  • What do you say?